YOU'VE GOT YOUR G3. NOW UPGRADE TO G2 WITHOUT GOING BACK TO SCHOOL.
You're a working G3 in Ontario. You've done your hours. The G2 (EX 9001) is the next step — and you don't have time to sit in a classroom for 8 months.
FlamePath drills the entire G2 written exam scope on your phone. Furnaces, boilers, Cat I–IV venting, controls, load calcs. Built for trades — no fluff, no lectures, just the questions you need to get right.
First lessons free. No card. Cancel anytime.
THE G3 → G2 PATH IN ONTARIO
Three steps. The third one is where most people get stuck.
HOLD A CURRENT G3
You already passed EX 9000 and have your G3 (or higher) certification card. ✅
DOCUMENT YOUR SUPERVISED HOURS
TSSA requires hands-on residential gas work hours under a licensed G2/G1. Your employer signs off. Confirm current hour requirements on TSSA's certification page before booking.
PASS THE EX 9001 WRITTEN EXAM
This is where FlamePath comes in. All multiple choice, code-application heavy, 75% to pass, up to 3.5 hours. We get you scoring 90%+ before you book.
YOUR FOUNDATION
- ✓Read a manometer and know what 3.5" w.c. means without thinking
- ✓Pressure test piping per CSA B149.1 §6
- ✓Identify natural gas vs propane appliance orifices on sight
- ✓Know your G3 fundamentals cold (gas properties, basic combustion, intro venting)
YOUR GAP TO CLOSE
- →Category II/III/IV vent sizing — and why you can't mix categories on a common vent
- →Two-pipe direct-vent terminations: clearances to windows, soffits, grade, mechanical air intakes
- →Sequence-of-operation diagnostics: which board input fails, what code blinks, what to swap
- →Heat loss calculations and matching BTU output to envelope load (no more "go up one size")
- →CSA B149.1 code lookup speed — the exam is open-book, but only if you can find the clause in 30 seconds
EVERY TOPIC ON THE EX 9001 — DRILLED
Each topic mapped to the exact CSA B149.1 clauses you'll be tested on. No padding.
HIGH-EFFICIENCY FURNACES
90%+ AFUE units. Sequence of operation, condensate management, secondary heat exchangers, ICM/Honeywell board diagnostics.
HYDRONIC & STEAM BOILERS
Cast iron vs condensing boilers, near-boiler piping, expansion tanks, aquastats, low-water cutoffs, zone valves.
VENTING CATEGORIES I–IV
B-vent vs PVC vs CPVC vs polypropylene. Termination clearances. Common venting rules. Sidewall vs vertical.
COMBUSTION AIR & LOAD CALCS
Confined vs unconfined spaces. Direct outdoor air supply. Heat loss calculations. BTU sizing residential.
CONTROLS & IGNITION
Hot surface, intermittent pilot, direct spark. Flame rectification. Pressure switches, gas valves, thermostat wiring.
CODE APPLICATION (B149.1)
The clauses you'll be asked about: piping, venting, regulators, appliance clearances, makeup air, CO testing.
WHY A STUDY TOOL — NOT ANOTHER COURSE
You already work full-time as a G3. You don't need someone to teach you what a manometer does. You need to drill the code-application questions until you stop second-guessing yourself.
George Brown's Gas Technician 2 program is 8+ months and runs on a school schedule. That's right for someone who hasn't worked the trade yet. It's overkill for a journeyman who just needs to pass EX 9001.
FlamePath is the supplement (or the standalone) — built around the exam, not around a curriculum. Repetition until automatic. Mistake review until you stop missing the same clause.
Pair it with your CSA B149.1 codebook. That's the whole system.
GET THE FREE G2 EXAM PREP CHECKLIST
Every topic on EX 9001, every CSA B149.1 clause to memorize, and a 4-week study schedule you can actually hit while working full-time. We'll email it now.
No spam. Unsubscribe anytime. We never sell emails.
FAQ
Do I need to take a college course to upgrade from G3 to G2?
No. Once you hold a G3 and have the required supervised work hours under a licensed G2 (or higher) gas fitter, you can register for the EX 9001 G2 referral exam directly with TSSA. A college program is one path — not the only path.
How many work hours do I need before writing the G2 exam?
TSSA sets the supervised-hours requirement and the supporting documentation. Confirm the current threshold on TSSA's certification page before booking EX 9001 — don't take a forum thread's word for it.
What is the EX 9001 exam?
EX 9001 is the TSSA written referral exam for G2 certification. All multiple choice. Heavy on code application from CSA B149.1 and O. Reg 212/01. The passing grade is 75%, with up to 3.5 hours to write, per the TSSA Certification Examination Preparation Guide (version March 2, 2023).
How is G2 different from G3?
G3 = fundamentals (gas properties, basic piping, combustion intro). G2 = applied residential (high-eff furnaces, hydronic boilers, Cat I–IV venting, ignition controls, load calcs, troubleshooting sequences).
Can I keep working as a G3 while studying?
Yes — that's the whole point. FlamePath is built for journeymen working full-time. 10 minutes a day on your phone. Lunch, after work, in the truck.